Install Chrome Extension Chrome Extension
Hyundai · Compact SUV · 2009–2015 Custom Search

Hyundai ix35 LM — Problems & Common Faults

Weaknesses, engine ratings and buying advice

★★★★★
3.0 / 5.0 · Based on 6 engine variants · How we rate
Everyday hassle beyond the engine: medium from 7 vehicle weaknesses (electrics, body, interior, suspension)

The Hyundai ix35 LM (2009–2015) is the European name for the second-generation Tucson — never sold as a Tucson in the EU, but badged as the ix35 from the start. That's not just a rebadge: Europe got a completely different engine lineup with several diesel variants and a 1.6L direct-injection petrol engine that the US Tucson LM never had. As a used buy, the ix35 is noticeably more relaxed than its predecessor — better perceived quality, less inspection drama, and the transferable five-year warranty is still active on well-maintained examples.

Engine choice: The D4HA (2.0L CRDi, 136–184 hp) is the heart of the ix35 — strong torque, efficient over long distances, and with the 6-speed manual the most recommended combination. EGR valve and DPF are the usual cost items with city driving. Injectors should be pressure-tested from 150,000 km (90,000 miles) onward at the latest. The D4FD (1.7L CRDi, 115–116 hp) is the understated option — a patient long-distance engine, with timing chain wear documented in isolated cases. The cheaper-to-run choice for less demanding drivers. The G4FD (1.6L GDI, 135 hp) uses direct injection — carbon deposits on the intake valves from 60,000–80,000 km (35,000–50,000 miles), fuel additives recommended as prevention. The G4KD (2.0L MPI, 163 hp) is the simplest petrol: no direct injection, no carbon buildup, but 10+ L/100 km real-world with a heavy foot.

Gearbox: The 6-speed DCT on the 2.0 GDI (post-facelift) is known for judder under 30 km/h (19 mph) — manual variants are the lower-risk choice. The manual's clutch release bearing wears out around 80,000 km (50,000 miles) (replacement about $1,050, €950).

Suspension: Rear spring breakage documented — especially after towing use. Hood flutter at highway speed. Tailgate rust on early models.

Test drive: D4HA: warm the engine up, then do a full-load test (turbo boost issues only show up once warm). DCT (2.0 GDI): crawl in a parking garage, checking for judder. Feel the rear axle for broken springs. Service book: D4HA injectors, DPF service intervals. Check that the hood latch sits firm.

2026 market: Entry from $5,000 (€4,500). Diesel models in good condition: $7,700–$12,700 (€7,000–11,500). Petrol models cheaper — budget for higher fuel use.

Insider pick: D4HA 2.0 CRDi 136 hp manual, 2011–2013 model, under 130,000 km (80,000 miles), complete service history — the strongest combination of durability, economy, and availability.

Most Fun Engine

184 PS

ix35 · Diesel

ix35 top diesel with 184 hp, AWD and automatic: the touring machine

Decent

Generations


Engine Overview

The Hyundai ix35 LM is available with 7 engine variants — from 116 to 184 hp.

1.7L CRDi · Diesel· 116 PS
2009 2015

Compact 1.7L turbodiesel with common rail — Hyundai's mid-range diesel for SUVs and sedans. Good balance of power and economy, adequate torque for daily use. DPF is the main theme — clogs in city-only use, regular motorway runs mandatory. Timing chain, interference engine. EGR valve cokes on short trips causing power loss. Diesel oil dilution occurs with frequent failed DPF regenerations — check oil level regularly. Cylinder head can crack under overheating, especially pre-2015 models. With consistent maintenance and regular long-distance driving, a reliable engine reaching 200,000+ km.

  • !! Diesel enters engine oil during DPF regeneration from 100,000 km

    When DPF regeneration cycles are interrupted, fuel is injected to burn off the soot filter. If regeneration aborts, diesel enters the engine oil — visible as a rising oil level.

    Symptoms: Rising oil level (diesel smell in oil), check engine light, blue exhaust cloud, increased consumption.
    300–2,000 $
  • !! Early engine block crack — coolant loss from 80,000 km

    Early D4FD variants (production 2011–2013) had known engine block cracks leading to coolant loss. Hyundai replaced affected engines under warranty; corrected design after 2013.

    Symptoms: Coolant loss without visible external leak, rising coolant temperature, white smoke from exhaust.
    2,000–6,000 $
  • !! Particulate filter clogging from 110,000 km

    All D4FD versions have a DPF that blocks on frequent short trips. Rising oil level from fuel contamination during failed regeneration is a warning sign.

    Symptoms: DPF warning light, power loss, engine limp mode, increased fuel consumption and rising oil level.
    900–2,800 $

+ 4 more engine weaknesses + vehicle weaknesses

2.0L CRDi · Diesel· 136 PS
2009 2015

Mid-range diesel — 2.0L CRDi with 100–136 kW for the SUV models. EGR valve fouls regularly. DPF clogs on short trips. Fuel-oil dilution (diesel in oil) is a serious concern — frequent oil changes and long-distance driving are mandatory. VGT actuator seizes occasionally. Timing chain rattles with neglected oil changes.

  • !! Fuel in engine oil (diesel dilution) from 80,000 km

    During DPF regeneration, diesel can enter the engine oil via post-injection. Above 2% dilution, bearing damage threatens. Leaking injector copper washers amplify the problem.

    Symptoms: Rising oil level without topping up, fuel smell on dipstick, sooty or thin engine oil at change.
    200–1,200 $
  • !! EGR valve fouling from 95,000 km

    D4HA 2.0 CRDi shows typical diesel EGR valve problems in short-trip use. Regularly check the intake manifold with swirl flaps for broken fragments.

    Symptoms: Engine power loss, rough idle, EGR fault codes, engine limp mode.
    300–900 $
  • !! DPF clogging from 120,000 km

    The D4HA DPF clogs on frequent short-trip use. Active regeneration requires motorway runs. Filter replacement is costly.

    Symptoms: DPF warning light, engine limp mode, power loss, increased fuel consumption.
    900–2,500 $

+ 4 more engine weaknesses + vehicle weaknesses

2.0L CRDi · Diesel· 184 PS
2009 2015

Mid-range diesel — 2.0L CRDi with 100–136 kW for the SUV models. EGR valve fouls regularly. DPF clogs on short trips. Fuel-oil dilution (diesel in oil) is a serious concern — frequent oil changes and long-distance driving are mandatory. VGT actuator seizes occasionally. Timing chain rattles with neglected oil changes.

  • !! Fuel in engine oil (diesel dilution) from 80,000 km

    During DPF regeneration, diesel can enter the engine oil via post-injection. Above 2% dilution, bearing damage threatens. Leaking injector copper washers amplify the problem.

    Symptoms: Rising oil level without topping up, fuel smell on dipstick, sooty or thin engine oil at change.
    200–1,200 $
  • !! EGR valve fouling from 95,000 km

    D4HA 2.0 CRDi shows typical diesel EGR valve problems in short-trip use. Regularly check the intake manifold with swirl flaps for broken fragments.

    Symptoms: Engine power loss, rough idle, EGR fault codes, engine limp mode.
    300–900 $
  • !! DPF clogging from 120,000 km

    The D4HA DPF clogs on frequent short-trip use. Active regeneration requires motorway runs. Filter replacement is costly.

    Symptoms: DPF warning light, engine limp mode, power loss, increased fuel consumption.
    900–2,500 $

+ 4 more engine weaknesses + vehicle weaknesses

1.6L GDI (Gamma) · Petrol· 135 PS
2009 2015

Naturally aspirated direct-injection from the Gamma family — 1.6L with 97–99 kW. Intake valve carbon buildup from GDI is the dominant theme — valves soot up without port washing. High-pressure fuel pump can fail at high mileage. Valve stem seals wear faster under GDI operation. Thermostat fails early. Timing chain stretches. An engine that deserves regular walnut-blasting valve cleaning.

  • !! High-pressure fuel pump failure from 110,000 km

    The GDi high-pressure fuel pump can fail. Using low-quality fuel or extended oil change intervals significantly increases the risk.

    Symptoms: Extended cranking time, stumbling at low rpm, engine cut-out, fuel pressure fault code.
    600–1,400 $
  • !! Valve carbon buildup (GDi system) from 70,000 km

    GDi direct injection no longer washes the intake valves with fuel. Carbon deposits impair gas exchange, leading to rough running and power loss.

    Symptoms: Rough idle, hesitation on acceleration, increased fuel consumption, misfires on a cold engine.
    300–700 $
  • !! Timing chain stretch from 120,000 km

    Despite a robust roller chain, chain noise occurs from 100,000–150,000 km in many cases. In extreme cases the chain can jump and strike valves.

    Symptoms: Rattling from the engine bay, particularly after cold start; check engine light from camshaft sensor fault.
    500–1,000 $

+ 3 more engine weaknesses + vehicle weaknesses

2.0L GDi (Nu) · Petrol· 163–166 PS
2013 2015

The Nu 2.0 GDi is the direct-injection variant of the Nu engine family producing 173 hp / 129 kW. Like all early GDi units it is prone to intake valve carbon buildup and elevated oil consumption at higher mileages. The 2014–2015 model years were subject to NHTSA recall 20V-750 for engine fire risk; verifying KSDS software and engine condition is essential when buying older examples.

  • !! Recall NHTSA 20V-750: Engine compartment fire while driving

    NHTSA recall 20V-750 covers Forte YD 2014–2015 with the Nu GDi engine: piston damage and oil loss can cause overheating and engine compartment fire. Dealers inspect for leaks, run engine tests, and update the Knock Sensor Detection System software at no charge.

    Symptoms: Smoke or flames from the engine bay, engine noises, sudden loss of power shortly before fire.
    0–0 $
  • !! High-pressure fuel pump and cam follower wear from 100,000 km

    On the GDi high-pressure pump the roller cam follower wears down, reducing pump lift and collapsing fuel pressure. In the worst case fuel enters the oil and wears the camshaft too; replace the follower together with the pump.

    Symptoms: Hard starting, power loss, ticking from the pump, fuel smell in the oil, possible limp mode.
    500–1,200 $
  • !! Elevated oil consumption via piston rings from 80,000 km

    Nu GDi engines show rising oil consumption from around 80,000 km (50,000 miles). The root cause is wider piston ring gap tolerances allowing oil to enter combustion. Typical symptom: blue smoke on cold start or under load.

    Symptoms: Blue smoke on cold start or under load, dropping oil level between service intervals, oil consumption exceeding 0.5 l / 1,000 km.
    1,000–4,000 $

+ 2 more engine weaknesses + vehicle weaknesses

2.0L MPI (Nu) · Petrol· 154 PS
2013 2015

Two-litre naturally aspirated from the Nu family — Hyundai's most sold engine in the compact class. Notorious for the piston ring/cylinder bore problem: rings wear prematurely, bores get damaged — worst case engine destruction with fire risk. NHTSA recall 21V301 covers US 2019–2021 models. Timing chain stretches — cold-start rattle is the warning. Oil consumption is endemic — subject of US class actions. Water pump wears early. Regular oil level checks and short change intervals (8,000–10,000 km) are mandatory.

  • !! Timing Chain Stretch and Jumping from 120,000 km

    The timing chain stretches noticeably earlier under high-rpm use. The chain rarely breaks outright, but jumps frequently, causing valve-to-piston contact. With gentle driving, 300,000 km service life is possible.

    Symptoms: Rattling on cold start, later also when warm; sudden engine damage from a jumped chain without warning.
    600–1,400 $
  • !! Piston Ring Oil Consumption (Class Action Affected) from 80,000 km

    The G4NA Nu is part of the class-action lawsuit against Hyundai for systemic oil consumption caused by defective piston rings. Oil scraper rings made from material that is too hard break and cause cylinder bore abrasion. Consumption can exceed 1 L/1,000 km.

    Symptoms: Very high oil consumption, blue smoke, oil pressure warning, knocking
    2,000–6,000 $
  • !! Recall 21V301: Nu Engine Piston Ring Scuffing — Stall/Fire from 60,000 km

    NHTSA recall 21V301 affects 2019–2021 Kona, Elantra and Veloster with 2.0L Nu MPI: piston rings were not properly heat-treated — seized connecting rod bearing, engine block perforation and fire risk.

    Symptoms: Knocking or rattling from engine; oil pressure warning light; sudden engine stall; in severe cases fire
    0–0 $

+ 1 more engine weaknesses + vehicle weaknesses

2.0L MPI (Theta II) · Petrol· 163–166 PS
2010 2013

Two-litre four-cylinder of the Theta II family with multi-point port injection, die-cast aluminium block, dual CVVT (including the exhaust side), a BorgWarner silent timing chain and 10.5:1 compression; output is about 119–121 kW. A documented issue is the connecting rod bearing recall series on Theta II engines of model years 2011–2014, caused by metal debris from manufacturing that disrupts oil flow around the crankshaft; the recalls do not clearly state which variants are affected. When buying, check the recall status by VIN and listen for bearing noise and check the oil level.

  • !! Connecting rod bearing damage from metal swarf (recall) from 100,000 km

    Manufacturing metal swarf in the crankshaft oil gallery blocks oil supply to the connecting rod bearings. Leads to progressive bearing wear, engine seizure and engine fire. Worldwide mass recall.

    Symptoms: Knocking from the engine, check engine light, sudden engine failure, oil pressure drop; in the worst case, engine bay fire.
    3,000–8,000 $
  • !! Connecting rod bearing wear (Theta II MPI) from 80,000 km

    The Theta II architecture is prone to connecting rod bearing wear from oil sludge and manufacturing particles. The MPI variant G4KD is less affected than GDI models with fire recall, but the underlying issue exists.

    Symptoms: Knock from the engine that intensifies with rpm, check engine light, engine stop
    0–0 $
  • !! Timing chain rattle with low oil level from 100,000 km

    The G4KD develops hydraulic pressure loss in the chain tensioner with low oil level or dirty oil, causing pronounced chain rattle on cold start. A jumped chain damages valves.

    Symptoms: Loud rattling from the front of the engine on cold start, diminishing after warm-up
    500–1,500 $

+ 1 more engine weaknesses + vehicle weaknesses

Vehicle Weaknesses

WeaknessCost
!Steering joints: main inspection complaint

The steering joints on the ix35 are the most common inspection complaint. Worn joints lead to imprecise steering and are a safety risk.

Symptoms: Steering has play, clunking noises on steering inputs
from 80,000 km
Low

Test Reports

TÜV report

TÜV Report 2026

Below average

The ix35 shows significantly more faults than the SUV average, particularly at tie rod ends and rust.

2025-11
Breakdown statistics

ADAC Breakdown Statistics 2024

Below average

The ix35 shows elevated breakdown figures with focus on battery and starter.

2024-04
NHTSA Owner Complaints
Below average
1,134 complaints · 2009–2015
  1. 01 Engine
    581 ⚠ 6
  2. 02 Brakes
    245 ⚠ 8
  3. 03 Hydraulic
    176 ⚠ 2
  4. 04 Powertrain
    114 ⚠ 7
  5. 05 Other
    102

Top Reported Issues

⚠ Engine (581 complaints)
⚠ Brakes (245 complaints)
⚠ Hydraulic (176 complaints)
Source: NHTSA (nhtsa.gov) · 2026-04

Alternatives

Same Segment

Acura RDX TB3

Compact SUV (2013–2018)

Same Segment

Audi RS Q3 8U

Compact SUV (2013–2018)

Same Segment

Buick Encore Gamma-II

Compact SUV (2013–2022)

Same Segment

Ford EcoSport I

Compact SUV (2013–2022)

Same Segment

Ford Escape III

Compact SUV (2013–2019)

Same Segment

Mercedes-Benz GLA X156

Compact SUV (2013–2020)

Explore more

Known Problems and Issues +

A total of 42 weaknesses have been documented for the Hyundai ix35 LM (2009–2015) — 33 engine-related and 9 vehicle-related. Typical issues affect Steering, Electronics, Rust, Other.

ix35 (D4HA, 2009–2015) — Be Careful: Fuel in engine oil (diesel dilution), EGR valve fouling, DPF clogging. Power: 136 PS.

ix35 (D4HA, 2009–2015) — Be Careful: Fuel in engine oil (diesel dilution), EGR valve fouling, DPF clogging. Power: 184 PS.

ix35 (D4FD, 2009–2015) — Be Careful: Diesel enters engine oil during DPF regeneration, Early engine block crack — coolant loss, Particulate filter clogging. Power: 116 PS.

ix35 (G4FD, 2009–2015) — Be Careful: High-pressure fuel pump failure, Valve carbon buildup (GDi system), Timing chain stretch. Power: 135 PS.

ix35 (G4KD, 2010–2013) — Be Careful: Connecting rod bearing damage from metal swarf (recall), Connecting rod bearing wear (Theta II MPI), Timing chain rattle with low oil level. Power: 163–166 PS.

ix35 (G4NA, 2013–2015) — Be Careful: Timing Chain Stretch and Jumping, Piston Ring Oil Consumption (Class Action Affected), Recall 21V301: Nu Engine Piston Ring Scuffing — Stall/Fire. Power: 154 PS.

ix35 (G4NC, 2013–2015) — Be Careful: Recall NHTSA 20V-750: Engine compartment fire while driving, High-pressure fuel pump and cam follower wear, Elevated oil consumption via piston rings. Power: 163–166 PS.

What to watch out for with the Hyundai ix35? See the detailed listing of all engine and vehicle weaknesses in the sections above.

Frequently Asked Questions

What problems and weaknesses does the Hyundai ix35 LM have? +
The Hyundai ix35 LM has 33 known engine weaknesses and 9 vehicle weaknesses.
What should I look for when buying a used Hyundai ix35 LM? +
faq.watch_a_none
Which engine is recommended? +
Be careful: G4FD (1.6L GDI (Gamma)), G4NA (2.0L MPI (Nu)), G4KD (2.0L MPI (Theta II)), D4HA (2.0L CRDi), D4FD (1.7L CRDi), G4NC (2.0L GDi (Nu)). No engine is rated 'Good Choice'. The most fun to drive is the D4HA (2.0L CRDi).
Which Hyundai ix35 LM engine is the most fun? +
The {code} ({displacement}) offers the most driving fun in the Hyundai ix35 LM — rated: "Decent". {description} The strongest diesel step with all-wheel drive and torque-converter automatic pulls hard but costs the most to keep: EGR valve, particulate filter and injector coking, plus the dual-mass flywheel. Rear spring breakage after towing is especially relevant here, so anyone who tows should look closely.
Is the Hyundai ix35 LM worth buying used? +
The Hyundai ix35 LM requires careful consideration — choosing the right engine variant is crucial.
What horsepower variants are available for the Hyundai ix35 LM? +
The Hyundai ix35 LM is available with engine variants from 116 to 184 hp. Petrol: G4FD (1.6L GDI (Gamma)), G4NA (2.0L MPI (Nu)), G4KD (2.0L MPI (Theta II)), G4NC (2.0L GDi (Nu)). Diesel: D4HA (2.0L CRDi), D4FD (1.7L CRDi).

Last updated: February 2026 · All information without guarantee