Volvo XC70
Volvo's first five-cylinder turbodiesel with 2.4-litre common-rail injection. DOHC with 20 valves and Bosch EDC injection. Good torque delivery for comfortable cruising speeds; sensitive to fuel quality at high injection pressure.
Sensible base engine
Perfectly adequate for everyday use. At the limit on the motorway, competent in city traffic.
Engine Weaknesses 4
The copper ring seal under the injectors fails to seal properly. Hot exhaust gas escapes, burning oil and forming black soot crusts around the injectors — known as Black Death.
Symptoms: Black soot crusts visible around injectors, diesel/exhaust smell in engine bay, misfires, rough engine running.
Replace timing belt every 160,000 km or 10 years. Water pump is belt-driven — if the old pump blocks after a belt change, the new belt is destroyed immediately. Always replace together.
Symptoms: No warning signal. Missed service or old pump leads to engine damage.
EGR valve becomes clogged with soot particles and carbon deposits. When stuck closed power drops; when stuck open the engine runs rough and smokes.
Symptoms: Power loss, rough idle, increased fuel consumption, black smoke, P0400 fault code.
Hydraulic tappets are sensitive to oil quality. With substandard oil or extended change intervals they start knocking from about 100,000 km.
Symptoms: Ticking noise from valve train after cold start, often disappears after warm-up, in extreme cases permanent.
Vehicle Weaknesses 21
The rear subframe of the XC70 I (P2 platform, pre-2007) is known for corrosion. Heavy rust requires an expensive replacement of the entire rear axle assembly. The cause is inadequate cavity sealing and road salt.
The C70 I convertible top system is complex and failure-prone. Control modules, sensors, and hydraulic pumps fail frequently; repairs are expensive and require special tools.
The C70 I suffers from cylinder head problems like other Volvo models of that era. Repairs can exceed €7,000; always check coolant level and condition before buying.
The front axle of the V70 II is a major weak point: faulty control arms and engine mounts wear frequently and are regularly flagged by MOT inspectors. The repair is time-consuming.
The Geartronic automatic in the S60 I and V70 II requires a fluid change every 50,000–60,000 km, even though Volvo declared it maintenance-free. Missed fluid changes lead to harsh shifting and costly consequential damage.
Front axle control arms and wheel bearings wear prematurely. Engine mounts tend to make noise when accelerating and braking. Front axle repair costs €500–900.
The Haldex coupling on AWD models fails when the oil service is neglected or at high mileage. Regular oil changes every 30,000 km are essential.
The mechanical handbrake shows insufficient holding force on many S60 I and V70 II vehicles, which is flagged at MOT. Check cables and rear calipers.
The rubber bushings in the front control arms of the XC70 I wear early — often by 50,000 km. Knocking over potholes and imprecise steering are the result. Replacing both control arms is recommended.
The Haldex oil pump in the XC70 I wears when oil changes are overdue and loses its pumping capacity. Consequence: no drive at the rear axle, poor traction on snow and loose surfaces.
Like the V70 II and S60 I, the XC70 I steering rack is also prone to leaking rack seals. If the fluid level is neglected, the power steering pump can be damaged.
The front wheel bearings on the XC70 I are subjected to higher loads than on the V70 due to the greater vehicle weight and all-wheel drive operation. Noise from 80,000–120,000 km is typical.
Rust reliably forms under the C70 I window seals. Door bottom edges also corrode — particularly the rearmost exhaust mount bracket shows corrosion as early as year five.
The C70 I Cabriolet preferentially rusts on the inner wheel arch surfaces and sill ends. Moisture ingress through missing or worn wheel arch covers accelerates deterioration. Often only visible as paint bubbles.
The C70 I front axle shares the well-known P80/P2 weaknesses: control arm joints, strut top mounts, and anti-roll bar bushings wear at higher mileages. MOT criticism of worn joints is common.
The C70 I automatic gearbox develops shifting problems when oil changes are neglected: harsh shifting, delayed reverse gear engagement, and occasional gear hunting. Oil change every 60,000 km recommended.
The electric window regulators in the C70 I Cabriolet are prone to cable breaks and pulley failures. The window can then no longer be closed — particularly frustrating with a convertible roof. Typical problem after 10 years.
The ABS control unit in the C70 I suffers from cold solder joints on the circuit board. ABS warning light illuminates permanently and ABS stops working entirely. Reflow soldering is an inexpensive repair option; replacement unit is significantly more costly.
The audio and navigation system on the P2 platform (S60 I, V70 II, XC70 I) fails due to cold solder joints in the RTI control unit. Replacement costs €700 and up; professional re-soldering is cheaper.
Like all late-1990s Volvo models, the radio/navigation control unit fails through cold solder joints. Replacement units from breakers are inexpensive.
On older C70 I vehicles, the air conditioning loses refrigerant through porous hoses and the compressor. Convertible use places greater demands on the air conditioning. Compressor replacement or regas required.